GeezerVisonThe World Wide Web, restored to 800 pixels of glory. |
| Home|About|Gaming cabinet|Archives|How it works|Starter sites |
GeezerVison is showing stackoverflow.com — Newest 'usb' Questions Collectives™ on Stack OverflowFind centralized, trusted content and collaborate around the technologies you use most. Learn more about Collectives7,930 questions
Question list filters
Score of -5
-5
votes
1 answer
1
answer
99 views
99
views
Renesas FSP UART receive callback not firing in half-duplex RS-485 communication [closed]
I am developing firmware in e² studio using Renesas FSP. My goal is to establish half-duplex RS-485 communication between a Renesas MCU with RS485 and a PC using a RS485 - USB DTech adapter.
Hardware ...
Score of 0
0
votes
0 answers
0
answers
49 views
49
views
USB PID D-Input Rumble: Block Load Report returns all zeros on PXN V9 Gen2
I am trying to implement a force feedback (rumble) effect for the PXN V9 Gen2 steering wheel in D-Input mode.
While X-Input mode works perfectly by sending standard Xbox rumble packets, D-Input ...
Score of 0
0
votes
0 answers
0
answers
50 views
50
views
How to get a unique serial identifier for a PIC32 to USB device?
I have several PIC32's connected to a computer via a custom PCB to USB.
I have custom firmware flashed to these using the PICKIT 5 debugger/programmer.
I want to be able to identify these devices ...
Score of 0
0
votes
0 answers
0
answers
119 views
119
views
Understanding Android open accessory
I have created an electron app to provide the sync service that my business logic will be hosted from, and it would control an expo app (barebone) to accept info from the host.
The problem is I keep ...
Score of 0
0
votes
1 answer
1
answer
44 views
44
views
Endpoints/Pipes of Standard USB Classes
How can I find out which USB Device Classes use which Endpoints/Message Types?(document & page side/ code file) And do device classes introduce any overhead to the data packets I am sending?(not ...
Score of 0
0
votes
1 answer
1
answer
158 views
158
views
Pymodbus library communication delay
I have the following example code. This code updates the frequency setting of the motor currently in use and gives it a forward movement command. I also add a specific waiting time in seconds while ...
Score of 0
0
votes
1 answer
1
answer
63 views
63
views
Avrdude flash fails on MacOS Monterey
I'm stuck. I purchased an old refurbished MacOS laptop and cannot get avrdude to flash my development firmware. I'd appreciate some help getting avrdude to work on this machine.
I installed the FTDI ...
Score of -3
-3
votes
1 answer
1
answer
139 views
139
views
Can USB CDC receive data byte-by-byte in CDC_Receive_FS(), or is it always packet-based?
I’m working with an STM32 microcontroller using USB CDC (Virtual COM Port) and handling incoming data in CDC_Receive_FS(). I want to understand the behavior for UART-style communication:
If the host ...
Score of 1
1
vote
0 answers
0
answers
80 views
80
views
Android (Studio) + Dragino LA66 USB
I am working on an Android app to control a drone. I am using the Dragino LA66 USB LoRa device for comm. Unfortunately, I am having difficulty with getting a signal transmitted to my Arduino board.
...
Score of 2
2
votes
1 answer
1
answer
137 views
137
views
What is the right format of packets in ADB pull?
I am working on an embedded RTOS system, and I want to support ADB file pulling based on open-source USB stack.
I read the document about ADB protocol (https://github.com/cstyan/adbDocumentation), and ...
Score of 0
0
votes
1 answer
1
answer
363 views
363
views
How can I get a USB HID device to enumerate as a xinputhid.sys compatible device?
I'm trying to get an ESP32-S3 TinyUSB device to show up as an XInput compatible device on Windows.
There appears to be three ways to do this: XUSB, XInputHID & GIP, with a recommendation to use ...
Score of 1
1
vote
1 answer
1
answer
109 views
109
views
Failure to enumerate USB device with DWC2 USB host
I am working on an embedded RTOS system for a 32-bit MIPS SOC, which supports DWC2 OTG. (It can run Linux well.)
I ported an open-source USB stack to this system by following the porting guidance.
...
Score of -1
-1
votes
0 answers
0
answers
145 views
145
views
How to get count of physical USB ports on Windows (not changing when devices are attached) using Go?
I am working on a Windows application written in Go lang, and I need to programmatically determine the number of physical USB ports available on the system.
My requirement is:
The count should ...
Score of 0
0
votes
0 answers
0
answers
111 views
111
views
Question about PMA Layout and BTABLE Size on STM32F103
I have two possible interpretations of how the USB BTABLE and PMA layout work on the STM32F103.
I will provide two diagrams (Figure A and Figure B) to illustrate the scenario.
STM32F1 USB PMA
Scenario:...
Score of 0
0
votes
1 answer
1
answer
78 views
78
views
Electron crash due to libusb conflict between yoctolib-cjs and other USB libraries
I am developing a Windows Electron application and I suspect a USB / libusb conflict between the usb library and Yoctopuce’s JavaScript API (yoctolib-cjs/yocto_api).
When both are used in the same ...
Hot Network Questions
|
| You are visitor 01402503 — GeezerVison does not store the pages you look up. Best viewed with Netscape Navigator 4.7 or Internet Explorer 6 at 800×600. No cookies required. |